Universal-air-tools UT8777C Manuel d'utilisateur télécharger pdf

Manufacturer/Supplier Product Type

RPM

Cycles Per Min

Tel No Fax No(01494) 883300 (01494) 883237

Model No/Nos Serial No (if any)

Product Nett Weight

lbs

Recommended Use Of

Balancer Or Support

Recommended Hose Bore

Size - Minimum

Recommended Max.

Hose Length

Ins M/M Ft M

Foreseen Use Of The Tool

This die grinder is primarily designed for use with bonded abrasive

mounted point grinding wheels. It may also be used with steel rotary

files and carbide burrs provided their speed rating matches the speed

of the grinder.

This tool should not be fitted with cutting off wheels, saw blades, drill

bits, etc. If there is any doubt about the correct use of this product

contact your supplier for advice.

Also make sure that the shank size of the attachment to be driven

matches with the collet size fitted in the grinder and that the

maximum allowed running speed of the attachment exceeds that

marked on the grinder.

There are special rules governing the use of bonded abrasive

mounted point grinding wheels - for details see section "Operating".

Putting Into Service

Air Supply

Use a clean lubricated air supply that will give a measured air pressure

at the tool of 90 p.s.i./6.3 bar when the tool is running with the

lever/trigger fully depressed. Use recommended hose size and

length. It is recommended that the tool is connected to the air supply

as shown in figure 1. Do not connect the tool to the air line system

without incorporating an easy to reach and operate air shut off valve.

The air supply should be lubricated. It is strongly recommended that

an air filter, regulator, lubricator (FRL) is used as shown in Figure 1 as

this will supply clean, lubricated air at the correct pressure to the tool.

Details of such equipment can be obtained from your supplier. If such

equipment is not used then the tool should be lubricated by shutting

off the air supply to the tool, depressurising the line by pressing the

lever/trigger on the tool. Disconnect the air line and pour into the

intake bushing a teaspoonful (5ml) of a suitable pneumatic motor

lubricating oil preferably incorporating a rust inhibitor. Reconnect tool

to air supply and run tool slowly for a few seconds to allow air to

Work Stations

The tool should only be used as a

handheld hand operated tool. It is

always recommended that the

tool is used when standing on the

solid floor. It can be used in other

positions but before any such

use, the operator must be in a

secure position having a firm grip

and footing and be aware of the

extra safety precautions that must

be observed when using Grinding

Machines.

Air Pressure

Recommended Working

6.3

bar

PSI

Recommended Minimum

n/a

bar

n/a

PSI

Maximum

bar

100

PSI

Personal Safety Equipment

Use - Safety Glasses

Yes

Use - Safety Gloves

Yes

Use - Safety Boots

Use - Breathing Masks

Yes

Use - Ear Protectors

Yes

Page No 1

Right Angle Die Grinder

(6mm Collet)

UT8777C

1.377

0.626 3/8 10 30 10

25000

Includes - Foreseen Use, Work Stations, Putting Into Service, Operating,

Dismantling, Assembly and Safety Rules

Operator Instructions Important

Read these instructions carefully before installing, operating,

servicing or repairing this tool. Keep these instructions in a safe

accessible place.

Universal Air Tool Company Limited

Unit 8

Lane End Industrial Park

High Wycombe

Bucks

HP14 3BY

Noise Level Sound Pressure Level 80.0 dB(A)

Test Method Tested in accordance with Pneurop

test code PN8NTC1 and ISO Standard 3744

Vibration Level

Test Method Tested in accordance with ISO

standard 8662/1 & 8662/13

Less than 2.5

Metres / Sec²

1 2 3 4

Résumé du contenu

Page 1 - Work Stations

Manufacturer/Supplier Product TypeRPMCycles Per MinTel No Fax No(01494) 883300 (01494) 883237Model No/Nos Serial No (if any)Product Nett WeightlbsKgRe

Page 2 - Reassembly

OperatingSelect a suitable mounted point that has a free running speedhigher than the maximum running speed marked on the tool.Make sure that the diam

Page 3 - Ref No Part No Description

UT8777C Rear Exhaust Die GrinderPage No 3Mar 2000 Ver 1.0Ref No Part No Description1 308AH001 Throttle Lever2 308AH002 Spring Pin3 308AH003 Housing4 3

Page 4

DistributorNotesPage No 4Accessoriesclothing, ties, hair, cleaning rags, etc.11) Use only compressed air at the recommended pressure.12) Do not attemp

Commentaires sur ces manuels

Pas de commentaire

Universal-air-tools UT8777C Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Universal-air-tools UT8777C. Universal Air Tools UT8777C User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Universal-air-tools UT8777C